# Mounting & Installation

{% hint style="info" %}
Tips:

The camera should be 1450\~1550mm above ground.

The camera at this height can capture human face perfectly.
{% endhint %}

<figure><img src="/files/3rugnE4hAnLU5ReCuIcB" alt=""><figcaption></figcaption></figure>

### Installation of Rain Hood

1. Choose the suitable height of camera and put the label sticker on the wall.
2. According to the sticker, drill three 8 x 45mm for screws and one 5mm for wire outlet.

<figure><img src="/files/Z3GPONmcW9pGJw1cwZUo" alt="" width="240"><figcaption></figcaption></figure>

3. Insert 3 screw fixing seats into the screw holes.
4. Remove the sticker after drilling.
5. Lock the rain hood or rear cover with 3 screws.

<figure><img src="/files/Jq10jGwfO2EfbSqDZ59g" alt="" width="152"><figcaption></figcaption></figure>

6. Let wires(included) and network cable without RJ-45 plug go through rain hood and waterproof seal plug.
7. Connect RJ-45 Plug.

<figure><img src="/files/gmnw4w98Y9CQwnx88Oj1" alt="" width="196"><figcaption></figcaption></figure>

8. Plug waterproof seal plug into the cover groove at the bottom.

<figure><img src="/files/GfyiNWNnyhkP8zQhioHd" alt="" width="133"><figcaption></figcaption></figure>

9. Fix interface clamp to the device with 2 screws.

<figure><img src="/files/Bh3mhsRW4lXqrEshLK2y" alt="" width="176"><figcaption></figcaption></figure>

10. Hang up device with rain hood.

<figure><img src="/files/ANBLqk1pxoXHRlB8juG2" alt="" width="135"><figcaption></figcaption></figure>

11. Use wrench to lock the bottom of the device with 1 screw (different screws for rain hood and rear cover).

### Installation of Rear Cover

1. Choose the suitable height of camera and put the label sticker on the wall.
2. According to the sticker, drill three 8 x 45mm for screws and one 5mm for wire outlet.

<figure><img src="/files/vVkj7Wgy6BPNGglx3Akd" alt="" width="225"><figcaption></figcaption></figure>

3. Insert 3 screw fixing seats into the screw holes.
4. Remove the sticker after drilling.
5. Lock the rain hood or rear cover with 3 screws.

<figure><img src="/files/tcb4aHm9pkL83mZAFgCK" alt="" width="119"><figcaption></figcaption></figure>

6. Let wires(included) and network cable without RJ-45 plug go through rear cover and waterproof seal plug.
7. Connect RJ-45 Plug.

<figure><img src="/files/6x06O6nYeaFTx7gaakwG" alt="" width="154"><figcaption></figcaption></figure>

8. Plug waterproof seal plug into the cover groove at the bottom.

<figure><img src="/files/CiWDViwgDuAxd3gxoW4G" alt="" width="159"><figcaption></figcaption></figure>

9. Fix interface clamp to the device with 2 screws.

<figure><img src="/files/E745jftb7hk6OzFLlmPc" alt="" width="182"><figcaption></figcaption></figure>

10. Hang up device with rear cover.

<figure><img src="/files/9HiKMGJl6RXf96v7n1Xp" alt="" width="105"><figcaption></figcaption></figure>

11. Use wrench to lock the bottom of the device with 1 screw (different screws for rain hood and rear cover).

<figure><img src="/files/YM4bU0RrYYjmFDu8K9zZ" alt="" width="103"><figcaption></figcaption></figure>

<br>

&#x20;


---

# Agent Instructions: Querying This Documentation

If you need additional information that is not directly available in this page, you can query the documentation dynamically by asking a question.

Perform an HTTP GET request on the current page URL with the `ask` query parameter:

```
GET https://wiki.inels.com/intercom/technical-manual/ves-b101/mounting-and-installation.md?ask=<question>
```

The question should be specific, self-contained, and written in natural language.
The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.